Packet Tracer Routing Table
- Configure a Router with Packet Tracer: A Guide to Setting Up Routers
- Packet tracer routing table
- Packet tracer - inter-vlan routing challenge addressing table
Firstly, we ll configure the IP addresses of the PCs on Packet Tracer like below. PC0: 10. 2 255. 255. 0 GW: 10. 1 PC1: 10. 3 255. 1 PC2: 20. 0 GW: 20. 1 PC3: 20. 1 PC4: 30. 0 GW: 30. 1 PC5: 30. 1 Here, the gateway addresses of the PCs will be the IP address of router virtual interfaces. Each router virtual interface will have an IP addresses as gateway of one of the VLANs. Creating VLANs Now, let's configure our VLANs and assign the interfaces to these VLANs. Firstly we will create VLAN 2, 3 and 4. Then, we will enter the interface range and configure the interface range as access interface. Lastly, we will assign the interface to a specific VLAN with " switchport access vlan " command.
Configure a Router with Packet Tracer: A Guide to Setting Up Routers
Hello and welcome! In this tutorial, we'll do an overview of EIGRP and see how to configure it on a Cisco Router in Packet Tracer. Overview of EIGRP Enhanced Interior Gateway Routing Protocol (EIGRP) is an hybrid routing protocol possessing characteristics of both distance-vector and and link-state routing protocols. It was a proprietary Cisco routing protocol but Cisco decided to convert it to an open standard in 2013. Let's see some key features that makes EIGRP helpful especially for large and complex networks. It supports both IPv4 and IPv6 Supports classless routing and VLSM (Variable Length Subnet Masking) Allows route summarization on any router in the network Supports load balancing Supports MD5 authentication EIGRP uses a multicast address of 224. 0. 10 and uses Cisco's Reliable Transport Protocol (RTP) to send messages to the multicast address. It has a default administrative distance of 90, which is less than the default administrative distances of RIP and OSPF, implying that EIGRP routes will be preferred over RIP and OSPF routes.
Packet tracer routing table
- El reto del verano: conseguir bañarnos en un mar de ardora
- Packet tracer - inter-vlan routing challenge addressing table
- Packet tracer routing table in html
- Media Player Classic Home Cinema: MPC-HC download | SourceForge.net
- Enseñanzas esenciales dalai lama pdf para
- Packet tracer routing table definition
- Configure a Router with Packet Tracer: A Guide to Setting Up Routers
- 23. Blanca Miosi - La dama de Amazon en YO me publico en mp3(08/06 a las 00:30:00) 39:08 51819077 - iVoox
- Packet tracer routing table in php
- Packet tracer routing table in r
Packet tracer - inter-vlan routing challenge addressing table
Type interface fastethernet0/1 2. 20. 0 3. Type no shutdown At this point our router is configured properly. If you test out a ping, you will notice that the computers still don't communicate, however! Configuring The Gateway In Packet Tracer Our last step is to configure the gateway on each desktop computer. The gateway is the address we assigned to the Ethernet port that the desktop is connected to. It will allow the computer to interface with another network, so our ping won't work without it! Click on PC0 to bring up the configuration menu. Under global settings you will find a field for the gateway. Enter the corresponding IP address of the router's interface, which is 192. Then click the FastEthernet tab on the left column to set the actual computer's IP address to be on the network. Use 192. 2 for the IP address, and 255. 0 for the subnet mask. Do the same thing for PC1, only use 192. 1 for the gateway address, 192. You can confirm that your network works by sending out a packet of information from PC0 to PC1, and vice versa.